Rechercher dans le manuel MySQL
18.1.3.1 Single-Primary Mode
In single-primary mode
(group_replication_single_primary_mode=ON
)
the group has a single primary server that is set to read-write
mode. All the other members in the group are set to read-only
mode (with super-read-only=ON
).
The primary is typically the first server to bootstrap the
group. All other servers that join the group learn about the
primary server and are automatically set to read-only mode.
In single-primary mode, Group Replication enforces that only a
single server writes to the group, so compared to multi-primary
mode, consistency checking can be less strict and DDL statements
do not need to be handled with any extra care. The option
group_replication_enforce_update_everywhere_checks
enables or disables strict consistency checks for a group. When
deploying in single-primary mode, or changing the group to
single-primary mode, this system variable must be set to
OFF
.
The member that is designated as the primary server can change in the following ways:
If the existing primary leaves the group, whether voluntarily or unexpectedly, a new primary is elected automatically.
You can appoint a specific member as the new primary using the
group_replication_set_as_primary()
UDF.If you use the
group_replication_switch_to_single_primary_mode()
UDF to change a group that was running in multi-primary mode to run in single-primary mode, a new primary is elected automatically, or you can appoint the new primary by specifying it with the UDF.
The UDFs can only be used when all group members are running MySQL 8.0.13 or higher. When a new primary server is elected automatically or appointed manually, it is automatically set to read-write, and the other group members remain as secondaries, and as such, read-only. Figure 18.4, “New Primary Election” shows this process.
When a new primary is elected or appointed, it might have a
backlog of changes that had been applied on the old primary but
have not yet been applied on this server. In this situation,
until the new primary catches up with the old primary,
read-write transactions might result in conflicts and be rolled
back, and read-only transactions might result in stale reads.
Group Replication's flow control mechanism, which minimizes the
difference between fast and slow members, reduces the chances of
this happening if it is activated and properly tuned. For more
information on flow control, see
Section 18.6.2, “Flow Control”. From MySQL
8.0.14, you can also use the
group_replication_consistency
system variable to configure the group's level of transaction
consistency to prevent this issue. The setting
BEFORE_ON_PRIMARY_FAILOVER
(or any higher
consistency level) holds new transactions on a newly elected
primary until the backlog has been applied. For more information
on transaction consistency, see
Section 18.4.2, “Transaction Consistency Guarantees”. If
flow control and transaction consistency guarantees are not used
for a group, it is a good practice to wait for the new primary
to apply its replication-related relay log before re-routing
client applications to it.
18.1.3.1.1 Primary Election Algorithm
The automatic primary member election process involves each member looking at the new view of the group, ordering the potential new primary members, and choosing the member that qualifies as the most suitable. Each member makes its own decision locally, following the primary election algorithm in its MySQL Server release. Because all members must reach the same decision, members adapt their primary election algorithm if other group members are running lower MySQL Server versions, so that they have the same behavior as the member with the lowest MySQL Server version in the group.
The factors considered by members when electing a primary, in order, are as follows:
The first factor considered is which member or members are running the lowest MySQL Server version. If all group members are running MySQL 8.0.17 or higher, members are first ordered by the patch version of their release. If any members are running MySQL Server 5.7 or MySQL 8.0.16 or lower, members are first ordered by the major version of their release, and the patch version is ignored.
If more than one member is running the lowest MySQL Server version, the second factor considered is the member weight of each of those members, as specified by the
group_replication_member_weight
system variable on the member. If any member of the group is running MySQL Server 5.7, where this system variable was not available, this factor is ignored.The
group_replication_member_weight
system variable specifies a number in the range 0-100. All members default to a weight of 50, so set a weight below this to lower their ordering, and a weight above it to increase their ordering. You can use this weighting function to prioritize the use of better hardware or to ensure failover to a specific member during scheduled maintenance of the primary.If more than one member is running the lowest MySQL Server version, and more than one of those members has the highest member weight (or member weighting is being ignored), the third factor considered is the lexographical order of the generated server UUIDs of each member, as specified by the
server_uuid
system variable. The member with the lowest server UUID is chosen as the primary. This factor acts as a guaranteed and predictable tie-breaker so that all group members reach the same decision if it cannot be determined by any important factors.
To find out which server is currently the primary when
deployed in single-primary mode, use the
MEMBER_ROLE
column in the
performance_schema.replication_group_members
table. For example:
- +-------------------------+-------------+
- | MEMBER_HOST | MEMBER_ROLE |
- +-------------------------+-------------+
- | remote1.example.com | PRIMARY |
- | remote2.example.com | SECONDARY |
- | remote3.example.com | SECONDARY |
- +-------------------------+-------------+
The group_replication_primary_member
status variable has been deprecated and is scheduled to be
removed in a future version.
Alternatively use the
group_replication_primary_member
status variable.
Traduction non disponible
Le manuel MySQL n'est pas encore traduit en français sur l'infobrol. Seule la version anglaise est disponible pour l'instant.
Document créé le 26/06/2006, dernière modification le 26/10/2018
Source du document imprimé : https://www.gaudry.be/mysql-rf-group-replication-single-primary-mode.html
L'infobrol est un site personnel dont le contenu n'engage que moi. Le texte est mis à disposition sous licence CreativeCommons(BY-NC-SA). Plus d'info sur les conditions d'utilisation et sur l'auteur.
Références
Ces références et liens indiquent des documents consultés lors de la rédaction de cette page, ou qui peuvent apporter un complément d'information, mais les auteurs de ces sources ne peuvent être tenus responsables du contenu de cette page.
L'auteur de ce site est seul responsable de la manière dont sont présentés ici les différents concepts, et des libertés qui sont prises avec les ouvrages de référence. N'oubliez pas que vous devez croiser les informations de sources multiples afin de diminuer les risques d'erreurs.