switch
(PHP 4, PHP 5, PHP 7)
The switch statement is similar to a series of IF statements on the same expression. In many occasions, you may want to compare the same variable (or expression) with many different values, and execute a different piece of code depending on which value it equals to. This is exactly what the switch statement is for.
Note: Note that unlike some other languages, the continue statement applies to switch and acts similar to break. If you have a switch inside a loop and wish to continue to the next iteration of the outer loop, use continue 2.
Note:
Note that switch/case does loose comparison.
| Version | Description |
|---|---|
| 7.0.0 |
Multiple default cases will raise a E_COMPILE_ERROR error.
|
The following two examples are two different ways to write the same thing, one using a series of if and elseif statements, and the other using the switch statement:
Example #1 switch structure
<?php
if ($i == 0) {
echo "i equals 0";
} elseif ($i == 1) {
echo "i equals 1";
} elseif ($i == 2) {
echo "i equals 2";
}
switch ($i) {
case 0:
echo "i equals 0";
break;
case 1:
echo "i equals 1";
break;
case 2:
echo "i equals 2";
break;
}
?>
Example #2 switch structure allows usage of strings
<?php
switch ($i) {
case "apple":
echo "i is apple";
break;
case "bar":
echo "i is bar";
break;
case "cake":
echo "i is cake";
break;
}
?>
It is important to understand how the switch statement is executed in order to avoid mistakes. The switch statement executes line by line (actually, statement by statement). In the beginning, no code is executed. Only when a case statement is found whose expression evaluates to a value that matches the value of the switch expression does PHP begin to execute the statements. PHP continues to execute the statements until the end of the switch block, or the first time it sees a break statement. If you don't write a break statement at the end of a case's statement list, PHP will go on executing the statements of the following case. For example:
<?php
switch ($i) {
case 0:
echo "i equals 0";
case 1:
echo "i equals 1";
case 2:
echo "i equals 2";
}
?>
Here, if $i is equal to 0, PHP would execute all of the echo statements! If $i is equal to 1, PHP would execute the last two echo statements. You would get the expected behavior ('i equals 2' would be displayed) only if $i is equal to 2. Thus, it is important not to forget break statements (even though you may want to avoid supplying them on purpose under certain circumstances).
In a switch statement, the condition is evaluated only once and the result is compared to each case statement. In an elseif statement, the condition is evaluated again. If your condition is more complicated than a simple compare and/or is in a tight loop, a switch may be faster.
The statement list for a case can also be empty, which simply passes control into the statement list for the next case.
<?php
switch ($i) {
case 0:
case 1:
case 2:
echo "i is less than 3 but not negative";
break;
case 3:
echo "i is 3";
}
?>
A special case is the default case. This case matches anything that wasn't matched by the other cases. For example:
<?php
switch ($i) {
case 0:
echo "i equals 0";
break;
case 1:
echo "i equals 1";
break;
case 2:
echo "i equals 2";
break;
default:
echo "i is not equal to 0, 1 or 2";
}
?>
The alternative syntax for control structures is supported with switches. For more information, see Alternative syntax for control structures.
<?php
switch ($i):
case 0:
echo "i equals 0";
break;
case 1:
echo "i equals 1";
break;
case 2:
echo "i equals 2";
break;
default:
echo "i is not equal to 0, 1 or 2";
endswitch;
?>
It's possible to use a semicolon instead of a colon after a case like:
<?php
switch($beer)
{
case 'tuborg';
case 'carlsberg';
case 'heineken';
echo 'Good choice';
break;
default;
echo 'Please make a new selection...';
break;
}
?>
English translation
You have asked to visit this site in English. For now, only the interface is translated, but not all the content yet.If you want to help me in translations, your contribution is welcome. All you need to do is register on the site, and send me a message asking me to add you to the group of translators, which will give you the opportunity to translate the pages you want. A link at the bottom of each translated page indicates that you are the translator, and has a link to your profile.
Thank you in advance.
Document created the 30/01/2003, last modified the 26/10/2018
Source of the printed document:https://www.gaudry.be/en/php-rf-control-structures.switch.html
The infobrol is a personal site whose content is my sole responsibility. The text is available under CreativeCommons license (BY-NC-SA). More info on the terms of use and the author.
References
These references and links indicate documents consulted during the writing of this page, or which may provide additional information, but the authors of these sources can not be held responsible for the content of this page.
The author This site is solely responsible for the way in which the various concepts, and the freedoms that are taken with the reference works, are presented here. Remember that you must cross multiple source information to reduce the risk of errors.
